DWX-42W Wet Dental Mill | Roland DGA
Technical Support for

DWX-42W Wet Dental Mill


Featured Articles
Missing Software
DWX-42W Coolant tank maintenance


Search DWX-42W Documents & Knowledge Base Articles



Expand All | Collapse All
Windows 10
Dental Driver for DWX-52D, DWX-52DCi & DWX-42W. Version 1.30. Contains drivers for both 32 Bit and 64 Bit. Supports Windows 7, 8.1 & 10. WINX64 is 64 bit folder. WINX86 is 32 Bit folder.
18.75 MB
Windows 7
Dental Driver for DWX-52D, DWX-52DCi & DWX-42W. Version 1.30. Contains drivers for both 32 Bit and 64 Bit. Supports Windows 7, 8.1 & 10. WINX64 is 64 bit folder. WINX86 is 32 Bit folder.
18.75 MB
Windows 8
Dental Driver for DWX-52D, DWX-52DCi & DWX-42W. Version 1.30. Contains drivers for both 32 Bit and 64 Bit. Supports Windows 7, 8.1 & 10. WINX64 is 64 bit folder. WINX86 is 32 Bit folder.
18.75 MB
Firmware 1.30 updates the main board for the DWX-42W wet mill.
2.20 MB
This document will show you how to replace the spindle belt. ZSB-140 is the belt for the DWX-4 and ZSB-170 is for DWX-51D, DWX-52D, DWX-52DC & DWX-52DCi Dental mill.
2.05 MB
This supplementary document will guide you through proper tool setup, maintenance schedules, and coolant management for the DWX-42W wet mill.
269.23 KB
Guide to maintaining DWX-4W nozzle integrity.
76.91 KB
Safety Data Sheet for DGShape ZCH-XXXD dated 5/30/19
138.29 KB
This User Manual will walk users through the proper VPanel setup steps, operations, and maintenance procedures for the DWX-42W wet mill.
7.61 MB
This setup guide will walk users through the steps for proper installation of the DWX-42W wet mill.
6.99 MB
CliniCAD is design software for the dental clinic. This software allows the development of crown, inlay, onlay, and veneer restorations.
622.73 MB
VPanel is the maintenance and monitoring software for the DWX-52D, DWX-52DC, DWX-52DCi and DWX-42W dental mills. This update adds a sequence to automatic correction that will improve the milling accuracy of the DWX-52D.
63.48 MB
MillBox DGSHAPE Wet 2.6.3 is the latest installer for the DWX-42W and DWX-4W dental mills.
842.14 MB
MillBox DGSHAPE Wet 2.6.3 is the latest updater for the DWX-42W and DWX-4W dental mills.
618.59 MB
Walk-through of how to perform cleaning of your DWX-42W and performing Auto Correction
28.13 KB
The DWX-42W Training video series provides step by step procedures on: 1. Installation (Unboxing, Setup & Software Installation) 2. Initial Maintenance (Fill the Coolant Tank, Calibration, Spindle Run-in) 3. Daily Maintenance (Collet Maintenance)
26.39 KB
In this video, you will learn how to combine coolant additive, chelate agent, and distilled water to fill the coolant tank for your device
27.76 KB
In this video, you will learn how to start the spindle run-in procedure and the difference between a spindle run-in short and a spindle run-in long.
27.28 KB
​Old coolant can influence proper water flow in the system and the quality of the milling process